Charles University, Faculty of Mathematics and Physics, Prague, Czech Republic, EU
The Influence of Al-Mg-Sc-Zr Strips Preparation on Microhardness During Annealing at Elevated Temperatures - POSTER
PE34
KÜCHER Gregor
Montanuniversitaet, CDL-TM, Leoben, Austria, EU
Impact on Co Lixiviation Selectivity in CH2O2 by Cemented Carbide Substrate Parameters - POSTER
PE35
KUŠNÍR Jakub
Charles University in Prague, Prague, Czech Republic, EU
The Study of Compression Behavior of Al-Based Open-Cell Microcellular Foams - POSTER
PE36
LABER Konrad
Czestochowa University of Technology, Czestochowa, Poland, EU
Physical Modelling of the AlZn5,5MgCu Aluminium Alloy Bars Rolling Process in the RSP14/40 Three-High Skew Rolling Mill - POSTER
PE37
LEIBNER Michal
Charles University in Prague, Prague, Czech Republic, EU
Precipitation Hardening in As-cast AA6082 and AA5754 Comercial Alloys with Sc,Zr-addition - POSTER
PE38
MALCHARCZIKOVÁ Jitka
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Hot-compression Behavior of Ni-Al-Zr Alloys - POSTER
PE39
MASAYLO Dmitriy
Peter the Great St.Petersburg Polytechnic University, St.Petersburg, Russian Federation
Laser Cladding Nickel based Superalloy Inconel 625 - POSTER
PE40
MENUSHENKOV Vladimir
National University of Science and Technology, Moscow, Russian Federation
Microstructure and Properties Investigations of Alloys Prepared by Aging of Fe-Based Alloy Powders Mixtured with Nitrid Powders (BN, Si3N4, AlN) - POSTER
PE41
MOGUCHEVA Anna
Belgorod State University, Belgorod, Russian Federation
Investigation of Portevin-Le Chatelier Effect in Coarse-grained Al-Mg Alloys - POSTER
PE42
MORAVČÍK Igor
Brno University of Technology, Brno, Czech Republic, EU
Mechanical Properties of High Entropy Alloy TiC Reinforced In-situ Composite - POSTER
PE43
MOROZOVA Anna
Belgorod State University, Belgorod, Russian Federation
Effect of the Hot Rolling and Annealing on the Microstructure and Properties of Al-0.3%Zr -1%Fe-Si Alloys - POSTER
PE44
MROZ Sebastian
Czestochowa University of Technology, Czestochowa, Poland, EU
Properties of Joint Region in the Mg/Al Two-Layer Materials after Explosive Welding Process - POSTER
PE45
NADOLSKI Maciej
Czestochowa University of Technology, Czestochowa, Poland, EU
Zinc Recovery from Industrial Waste by Means of Hydro- and Pyrometallurgical Processes - POSTER
PE46
NOGA Piotr
AGH University of Science and Technology, Cracow, Poland, EU
Structural Features and Mechanical Properties of Rapidly Solidified AlSi Alloys - POSTER
PE47
OLEJŇÁK Juraj
Charles University, Faculty of Mathematics a Physics, Prague, Czech Republic, EU
Influence of Heat Treatment on Deformation Behaviour of Mg-Zn Alloys - POSTER
PE48
ONANKO Anatoliy Petrovich
Kyiv national university, Kyiv, Ukraine
Absorption Properties, Thermo-Mechanical Treatment Of Ag-Zn, Al, Ti Alloys, Expanded Polystyrene And Automated System - POSTER
PE49
OSTRÝ Milan
Brno University of Technology, Brno, Czech Republic, EU
Compatibility Tests of Metal-PCM Pairs Used in Thermal Energy Storage - POSTER
PE50
PANASIUK Katarzyna
Maritime University of Gdynia, Gdynia, Poland, EU
Detection of Damage in AlZn4.5Mg1 Aluminum Alloy by Acoustic Emission in Tensile Test - POSTER
PE51
PASEK Dorota
Silesian University of Technology, Katowice, Poland, EU
Heat Resistance of the Welded Joint from Fe40Al5Cr0,2TiB Intermetallic Alloy Made by TIG Method - POSTER
PE52
PINC Jan
Institute of Physics of the CAS, Prague, Czech Republic, EU
Processing and Characterization of Zinc Wire Prepared by One-Step Hot Extrusion with High Extrusion Ratio - POSTER
PE53
POLOZOV Igor
Peter the Great St.Petersburg Polytechnic University, St.Petersburg, Russian Federation
In-situ Synthesis of Titanium Alloys from Elemental Powders by Laser Additive Manufacturing - POSTER
PE54
PROKOFEV Pavel
Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, Moscow, Russian Federation
Phase-Formation in the Tb-Co-Cu System in a Range of 0-64 at % Tb - POSTER
PE55
RAJCZYK Paweł
Czestochowa University of Technology, Częstochowa, Poland, EU
Test of Wearing of Diamond Segments on Metallic Binders at the Treatment of Granite Surfaces - POSTER
PE56
RZEPA Sylwia
AGH University of Science and Technology, Dobřany, Czech Republic, EU
The Ti - Si Intermetallic Phases Synthesis by Using SHS Method - POSTER
PE57
SAGADIN Christoph
Montanuniversitaet Leoben / Nonferrousmetallurgy CDL-TM, Leoben, Austria, EU
High Temperature Corrosion of Magnesia based Refractory by Ferronickel Slags - POSTER
PE58
SIDOROV Evgeny
Vladimir State University, Vladimir, Russian Federation
Specification of the Full Equilibrium Phase Diagram of the Iron-Carbon System Based on the Theoretical and Experimental Investigations - POSTER
PE59
SKOTNICOVÁ Kateřina
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Optimizing the Microstructure of Low-REM Nd-Fe-B Sintered Magnet Using Tb3Co0.6Cu0.4Hx Addition - POSTER
PE60
SKOWRON Ewelina
MESKO S.A., Skarżysko-Kamienna, Poland, EU
Electrospark Deposition of Carbon Steel Using the Tungsten Electrodes - POSTER
PE61
SKRZEKUT Tomasz
AGH University of Science and Technology, Cracow, Poland, EU
Examination of Aluminum Matrix Composites Obtained by Powder Metalurgy and Strenghtened by AgO and CeO2 Particles - POSTER
PE62
STACHURA Ryszard
AGH University of Science and Technology, Cracow, Poland, EU
Influence of Selected Batch Properties on the Operation of Imperial Smelting Furnace - POSTER
PE63
STRUNG Václav
VSB - Technical university of Ostrava, Ostrava, Czech Republic, EU
Microstructure and Purity of NiTiZr-Based Alloys Prepared by Plasma Metallurgy Process - POSTER
PE64
SZABÓOVÁ Andrea
Charles University in Prague, Prague, Czech Republic, EU
Mechanical Properties of Mg-RE Alloys Studied by Acoustic Emission - POSTER
PE65
SZWED Bartłomiej
Kielce University of Technology, Kielce, Poland, EU
Wear Resistance Properties of Diffusion Bonded Joints between Titanium and Stainless Steel obtained by Al, Cu and Ni Intermediate Materials - POSTER
PE66
ŠAŠEK Stanislav
Charles University in Prague, Prague, Czech Republic, EU
Magnesium with Zr Alloying Element Processed by ECAP - POSTER
PE67
ŠERÁK Jan
University of Chemistry and Technology Prague, Prague, Czech Republic, EU
Variability of Mechanical and Corrosion Properties of Standardized Aluminium-Based Alloys - POSTER
PE68
TERYNKOVÁ Anna
Charles University in Prague, Department of Physics of Materials, Prague, Czech Republic, EU
The Effect of Cryogenic Milling on the Microstructure and Mechanical Properties of Sintered Ti-15Mo Alloy - POSTER
PE69
THOMAS Angerer
Institute of Nonferrous Metallurgy / Montanuniversitaet Leoben, Leoben, Austria, EU
Development of a New Recycling Process for Salt Slags from the Secondary Magnesium Production - POSTER
PE70
TSYGANOV Igor
Lipetsk State Technical University, Lipetsk, Russian Federation
Influence of Deformation on Structure and Mechanical Properties of Titanium-based Alloy Prepared by Self-propagating High Temperature Synthesis - POSTER
PE71
TUTAK Piotr
Czestochowa University of Technology, Institute of Mechanics and Machine Design Foundations, Czestochowa, Poland, EU
Application of FEM in Pressure Pulse Test Simulation for Charge Air Cooler - POSTER
PE72
VÁVRA Tomáš
Charles University in Prague, Department of Physics of Materials, Prague, Czech Republic, EU
Superplastic Deformation of Ultrafine-Grained Magnesium Alloys - POSTER
PE73
WAŚ Joanna
BOSMAL Automotive Research and Development Institute Ltd., Bielsko-Biała, Poland, EU
Verification of Corrosion Resistance of Aluminium 5754 Alloy in Neutral Salt Spray Environment - POSTER
PE74
WAŚ Joanna
BOSMAL Automotive Research and Development Institute Ltd., Bielsko-Biała, Poland, EU
Comparison of Strength Properties of Aluminium 5754 Alloy after Exposure in Neutral and Acetic Corrosive Environments - POSTER
PE75
WIBNER Stefan
Non-ferrous metallurgy - Montanuniversitaet Leoben, Leoben, Austria, EU
Determination of Free Aluminum Content in Dross with Liquid Salt Slag in the TBRC - POSTER
PE76
WŁODARSKA Julia
AGH university of science and technology, Cracow, Poland, EU
Selected Methods of NDT Uncertainty Analysis for Quality Rating in Multilayer Ceramic Moulds - POSTER
PE77
ZLAMAL Tomas
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
The Influence of Microgeometry of Cutting Tool on Dynamic Load of System - POSTER
PE78
ZOBAČ Ondřej
Department of Inorganic Chemistry - functional materials, University of Vienna, Vienna, Austria, EU
Experimental Description of the Al–Cu Binary Phase Diagram - POSTER
PE79
ŻYBURA Maciej
AGH University of Science and Technology, Cracow, Poland, EU
Thermal Imaging Analysis of the Structure of Multilayer Ceramic Molds - POSTER
